
Silicomanganese 60/14 vs 65/15: How Steel Buyers Compare Grades
For steel buyers, a silicomanganese 60/14 vs 65/15 comparison starts with the melt requirement rather than the quoted price per tonne. A 60/14 quotation may appear cheaper per tonne than a 65/15 offer, yet the manganese and silicon delivered to the melt, allowable phosphorus, lump-size distribution and fines can change the purchasing decision. None of those differences is established by the grade label alone.
This guide is written for steelworks and procurement teams buying silicomanganese as a deoxidizing and alloying addition. It explains how to compare the offers against the intended steel chemistry and a clear RFQ, without treating a supplier's example analysis as a universal industry specification.
What Silicomanganese 60/14 vs 65/15 Actually Means
In commercial listings, SiMn 60/14 generally signals an offer built around at least about 60% manganese and 14% silicon; 65/15 generally signals at least about 65% manganese and 15% silicon. These shorthand names are useful when searching for suppliers, but they do not by themselves fix the permitted levels of carbon, phosphorus and sulfur, the size tolerances or the certificate requirements.
Silicomanganese is a ferroalloy used to introduce manganese and silicon into steel. Ferroglobe describes it as an important steel deoxidizer and distinguishes standard, refined and super-refined product families. An alloy sold as 65/15 is not automatically the correct substitute for 60/14 in every melt recipe; the steelmaker must consider the planned additions, the actual COA and the permitted impurity budget.
The Chemistry Comparison: Start With Mn and Si, Then Examine C, P and S
Manganese and silicon: the target additions
The nominal difference between 60/14 and 65/15 is a higher stated manganese and silicon level in the latter. The minimum specified values are not the actual values in the shipment: the batch certificate may show higher results. For the same delivered alloy mass, 65/15 at its stated minima contains more manganese and silicon than 60/14 at its minima. Actual recovery into the steel depends on the furnace practice and cannot be inferred from the purchase specification alone.
A purchasing team should therefore compare the alloy requirement with the steel grade's targeted Mn and Si addition. If a plant is adjusting an existing recipe, approval belongs to the metallurgical or quality team, not to the price comparison alone. A nominally higher grade might reduce a theoretical alloy-addition mass in some circumstances, but it is not proof of better yield, fewer losses or lower cost per finished tonne.
Carbon, phosphorus and sulfur: limits rather than afterthoughts
Carbon and phosphorus limits can make the two offers non-interchangeable even where manganese and silicon are acceptable. Carbon has to fit the steel's chemistry and operating route. Phosphorus is especially important for grades with tight residual limits; it cannot be ignored because the offer is described as standard silicomanganese. Sulfur should likewise be reported as a measured result against the purchaser's accepted maximum.
For each constituent, insist on clarity about whether the value is a guaranteed minimum, a guaranteed maximum, a typical range or an actual batch test. A quoted 'P 0.25%' can mean something very different from 'P 0.25% max'. The agreed chemistry should be written into the purchase specification and checked against the actual lot or cast result.
Why Published 60/14 and 65/15 Specifications Do Not Match Exactly
Published seller examples illustrate the practical problem. BDG Group's silicomanganese table lists, for 60/14, Mn 60% minimum, Si 14% minimum, C 2.50% maximum, P 0.30% maximum and S 0.03% maximum. For its 65/15 entry, it shows Mn 65% minimum, Si 15% minimum, C 2.25% maximum, P 0.25% maximum and S 0.03% maximum.
TMA International publishes a different set of reference limits: its 60/14 lists Mn 60–65%, Si 14–16%, C not above 2.0%, P not above 0.25% and S not above 0.04%. Its 65/15 lists Mn 65–68%, Si 15–17%, C not above 2.0%, P not above 0.20% and S not above 0.04%. These are supplier-published examples, not two versions of a universal guaranteed specification.
Those differences are enough to change a quotation decision where the melt has a tight phosphorus or carbon ceiling. Buyers should not assume one seller's declared range carries over to all other producers. Ask for a signed or otherwise verifiable offer specification and a representative recent batch or heat COA for the grade actually being proposed.
Standards: Do Not Mistake Commercial Grade Names for Standard Grade Designations
The active ASTM A483/A483M-10(2025) specification covers silicomanganese Grades A, B and C with requirements for manganese, silicon, carbon, phosphorus, sulfur and size tolerances. Those formal ASTM designations are not simply a renaming of commercial 60/14 and 65/15 grades. If ASTM compliance is required, state the exact designation and applicable grade, and verify the supplier's product against that standard instead of inferring compliance from a marketplace label.
A separate, time-sensitive point applies to Indian Standard references. The Bureau of Indian Standards announced that IS 1470:2025 superseded IS 1470:2013, with implementation required by 15 April 2026 for the applicable licensing framework. The BIS notice says the revised standard changes the grade structure and particle-size provisions. If a current offer claims BIS conformity, check the revised edition and the specific product grade; an old IS 1470:2013 label should not be accepted without clarification.
These are standards and edition controls, not a claim that every shipment to every country must meet ASTM or BIS. Which reference is appropriate depends on the contract, buyer specification, product origin and applicable destination requirements.
Particle Size, Fines and Handling Are Part of the Delivered Grade
Silicomanganese commonly reaches steel plants as crushed metallic-looking alloy lumps. The RFQ must define the usable size fraction for the plant's charging arrangement, not simply mention 'lumps'. Published commercial offerings include ranges such as 10–50 mm and 10–100 mm, but the acceptable range depends on the buyer's equipment and process.
Specify how sizing is verified: upper and lower sieve cutoffs, acceptable oversize and undersize percentages by weight, sampling location and the point at which tolerance applies. Fines may increase during repeated loading, storage and discharge; a source's nominal grading may not represent the distribution at receiving. The BIS revision guidance explicitly highlights modified size provisions and the possibility of agreed alternative size ranges or tolerances.
Handling and packaging should match the requested lot and route. A bulk shipment, jumbo bag or smaller packed lot may need different handling controls. Ask whether the quotation includes screening, secure packaging, lot identification and protection against excessive contamination or loss. Never assume the same size tolerance applies automatically to all suppliers or delivery bases.

COA Review: Can the Chemistry Be Traced to the Offered Shipment?
For every offered grade, request a Certificate of Analysis or mill test document that identifies the product and nominal grade, issuer, test date, cast/heat or batch reference and the measured Mn, Si, C, P and S values. Where required, include relevant trace elements and the laboratory or testing method. Check whether the attached document is a lot-specific result or merely a typical product specification.
Connect the COA to the quantity and identification of the cargo. Confirm whether one shipment includes several casts or lots, and whether the supplier will report results separately where the acceptance scheme requires it. A clean-looking certificate from an unrelated heat is not proof of conformity for the dispatched material.
The buyer should also establish a mutually understood sampling, inspection and acceptance mechanism. The specification should describe when and where size and chemistry are checked, who draws a representative sample and what happens to nonconforming material. A vague reference to 'SGS inspection' or 'manufacturer certificate' is not a substitute for an agreed test and acceptance scope.
An RFQ That Makes Both Grades Comparable
A useful request allows suppliers to quote 60/14, 65/15 or an approved alternative without mixing the acceptance criteria. Include the following information in a clear product-specific inquiry:
Full material name: Silicomanganese (SiMn), with the requested 60/14 or 65/15 commercial grade.
Steelmaking application and furnace or charging route, where relevant to sizing and selection.
Required Mn and Si minima or specified ranges, plus C, P and S maxima; identify any tighter special limits.
Named applicable standard and edition only where required, with the actual grade designation.
Nominal lump-size band, allowable fines and oversize, and the agreed measurement point.
Quantity in metric tonnes, whether it is a trial or recurring requirement, and any lot-separation conditions.
Packaging and handling requirements, including bulk versus bags and cargo identification.
Destination and requested delivery location or Incoterms basis.
Required technical documents: product specification, lot-specific COA and agreed sampling/inspection evidence.
Clear treatment of substitutions, deviations and alternative grades on the quotation.
How to Compare the Commercial Offers Without Losing the Technical Basis
Compare price only after the offers have been normalized to one accepted specification—or clearly classified as different technical alternatives. Record the delivered basis, moisture or contamination allowance if relevant, packaging, actual particle-size distribution and the evidence provided for impurity limits. A quote with a lower price per tonne may not have a lower useful addition cost if its chemistry, fines or handling losses differ.
For a like-for-like procurement, require supplier deviations to be identified line by line. For a proposed switch from 60/14 to 65/15, assess the chemistry and practice with the plant metallurgist and, when justified, validate it through controlled production trials. Do not promise a particular manganese recovery, reduction in alloy use or steel-quality improvement without plant data.
Common Procurement Errors Worth Eliminating
The most expensive errors usually begin with seemingly minor assumptions: reading the grade name as a complete contract, comparing supplier 'typical values' with guaranteed limits, overlooking phosphorus, accepting a generic COA, allowing unlimited fines and treating bulk and bagged offers as identical delivery conditions. Any one of these can create a mismatch between the RFQ, the order and the received alloy.
A better process is to establish the steelmaking requirement, make the chemistry and size acceptance explicit, verify that the evidence applies to the offered lot, then review the commercial terms. This is a technical purchasing discipline, not a claim that the more expensive nominal grade is always better.
Submitting a Silicomanganese Sourcing Inquiry to SAYIMO
SAYIMO's steel and metallurgy sourcing scope includes ferro silico manganese as an inquiry-based sourcing category. Buyers can submit a specification-led sourcing inquiry with their required SiMn grade, chemistry, lump size and fines tolerances, quantity, destination and available technical specification for review. The sourcing route, producer, origin, availability and commercial terms are considered for the individual requirement rather than presumed from a website listing.
For context on a different alloy family, our Ferrosilicon 75 buyer guide discusses how silicon level, impurity limits and particle size affect FeSi purchasing. Silicomanganese must be qualified separately because it introduces both manganese and silicon and carries its own chemistry and acceptance requirements.
Sources and Verification
Source verification: 7 November 2026. The seller chemistry examples are indicative published specifications, not universal guarantees. Formal compliance and available lots must be confirmed for each individual inquiry.



Comments